Firmware FAQ

From DD-WRT Wiki

Revision as of 19:19, 7 October 2006 by AycheKay (Talk | contribs)
Jump to: navigation, search

Contents

How can I tell if my router is truly bricked?

Since this question involves many variables, we do not have an article for it yet. Try resetting to firmware defaults.

I think I've bricked my router!

There's a lot of variables in answering this question and we don't have articles to cover all the different situations. But, for now, search the Wiki and the forums for more information, just to verify that it's truly bricked. Don't forget to try holding in the reset button for 30 seconds. Then see: Recovering from a bad flash.

Is my router supported?

If you have to ask, probably not. See Supported Devices
Linksys WRT54G v7.0 models are not supported and probably never will be.

I have a Linksys version 5 or 6 router.

We have a page in the Wiki just for you. Version_5_And_6_Router_Information

What router should I buy?

In short, the Buffalo WHR G54s is the cheapest 100% compatible wireless router. For more information see Recommended Devices

Where do I download firmware?

http://www.dd-wrt.com/dd-wrtv2/downloads.php

What's the difference between the different DD-WRT versions?

See this

How do I install DD-WRT firmware?

Make sure you have a compatible router. Make sure you follow all the instructions, especially the part about resetting your router before flashing and in between each additional flash. See Installation

How do I upgrade my firmware with TFTP?

Flashing with TFTP must not be seen as the standard procedure for flashing: only use it when you are specifically told to do so (for example in the specific instructions for flashing your brand or type of device). Normally, the GUI flashing method should be used; it should be perfectly adequate for any standard situation. See Installation

What's the default username and password?

Starting with v23 SP1, the default username is root and the default password is admin.

How do I access the router's settings?

If you have DD-WRT installed, your router's settings should be accessible by opening a web browser and typing http://192.168.1.1/ in the address bar. If you have changed the LAN IP address on the router, you'll need to type in the correct one instead. If your router doesn't have DD-WRT installed yet, try http://192.168.1.1/ or http://192.168.0.1/ or else consult the manufacturer's documentation. Whether you have DD-WRT installed or not, make sure your computer has an IP address in the same scheme as the router. Try pinging the router to make sure you have connectivity. Try accessing the settings using a network cable instead of accessing them wirelessly. Try clearing your browser's cache. If you've been messing with proxy settings, make sure you didn't leave some incorrect proxy settings in your browser. And last but not least, try holding the reset button in for 30 seconds. It will reset all your settings back to defaults, but it should let you back into the router. Also see the Wiki article on the Web Interface.

Why can't I access the web configuration for my router?

If you've read the previous question and it didn't help, then your router's HTTP Daemon might not be running. See "Regaining Access". The other problem that currently causes this is incorrect HTTP Redirector settings, found at "Administration" > "Hotspot". By default the HTTP Redirector is disabled. If you enabled the HTTP Redirector and you suspect you might have created a problem, see the fix on this page: HTTPRedirect

How do I get the Internet to work on my router?

"After upgrading to DD-WRT, my Internet doesn't work anymore." A common problem for which there is no single common fix. Understanding networking, subnets, NAT, etc. would be in your best interests to troubleshoot this issue. For DSL users, generally PPPoE is the best option. You may need to call your Internet Service Provider (ISP) for settings that are particular to your connection. Some ISP's expect the MAC address of your modem to be communicating with their servers so you may need to use the "Clone MAC Address" feature. Make sure you use the correct username and password. For cable and satellite users, generally DHCP is the correct setting. For Comcast Cable users, be sure to disable STP. For users trying to share a dial-up connection, you'll need to read the Wiki article Sharing Dial-Up. At any rate, it's a near 99% chance that the problem is not your DD-WRT firmware, but instead your lack of understanding with networking.

I'm having lots of TX (transmit) errors.

Try setting the Ack Timing to 0. If you have the the transmit power turned up higher than 84 mW, turn it down to 84.

How high should I set the transmit power on my router?

Somewhere around 84 mW is considered to be the best setting for maximum power with minimum noise. The forums have had discussions about what power level is safe, with little conclusion. Use common sense and don't set the power higher than you really need to. If you're trying to get more range, consider using a different antenna and make sure you have a clear line of sight, two of the most critical factors in your router's range.

How can I increase my wireless range?

Many factors affect your range. Consider getting a good antenna and try setting up your wireless devices with a clear line of sight. Best range is achieved by using one directional parabolic dish or yagi antenna and then disabling the other antenna on your router. Try increasing your router's transmit power to 84 mW.

Links

How-To's Many Walk-Throughs for Different DD-WRT Configurations
Articles Some Articles on subjects like Wireless Modes, Router Modes, etc.
Glossary Wireless Networking Terms and Definitions along with DD-WRT Feature explanations