D-Link DIR-880L
From DD-WRT Wiki
Revision as of 20:19, 3 June 2023 (edit) Kernel-panic69 (Talk | contribs) (→Procedure - (add upgrade procedure)) ← Previous diff |
Current revision (20:21, 3 June 2023) (edit) (undo) Kernel-panic69 (Talk | contribs) m (→Prerequisites - (change warning color scheme)) |
||
Line 67: | Line 67: | ||
==Prerequisites== | ==Prerequisites== | ||
- | '''<span style="color:#ff0000">WARNING</span> | + | '''<span style="color:#ffffff; background:#ff0000"> **WARNING**: </span>''' There was a period of time that there were specific factory-to-ddwrt.bin files required; this '''''should''''' be fixed in current releases. If flashing current release factory-to-ddwrt.bin files results in a boot loop or brick, please refer to the Recovery section below to enter Emergency Room to flash a known good file from [https://app.box.com/s/b4v1s342ef2dpd52j02lqtuzi1oiipco/folder/42086693204 here]. |
'''NOTE:''' [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=323436 03-05-2020-r42617] is a known good initial flash build. See [https://forum.dd-wrt.com/forum/viewtopic.php?t=268579&postdays=0&postorder=asc&start=381]<br> | '''NOTE:''' [https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=323436 03-05-2020-r42617] is a known good initial flash build. See [https://forum.dd-wrt.com/forum/viewtopic.php?t=268579&postdays=0&postorder=asc&start=381]<br> | ||
'''NOTE:''' See [[Firmware_FAQ#Which_router_should_I_buy.3F|Where do I download firmware?]] for information on where to find firmware images. | '''NOTE:''' See [[Firmware_FAQ#Which_router_should_I_buy.3F|Where do I download firmware?]] for information on where to find firmware images. |
Current revision
English • Deutsch • Español • Français • Italiano • 日本語 • Polski • Português • Русский • Svenska • 中文(中国大陆) • 中文(台灣) • |
Contents |
[edit] Introduction
[edit] Hardware Specifications
FCC ID: | KA2IR880LA1 |
---|---|
IC ID: | 4216A-IR880LA1 |
CPU1: | Broadcom BCM4708A0 (800 MHz, 2 cores) |
FLA1: | 128 MB (Spansion S34ML01G100TFI00) |
RAM1: | 256 MB (EtronTech EM6GD16EWXC-15H) |
USB ports: | 1xUSB 3.0, 1xUSB 2.0 |
WI1 chip1: | Broadcom BCM4360 |
WI1 802.11 protocols: | an+ac |
WI1 MIMO config: | 3x3:3 |
WI2 chip1: | Broadcom BCM4360 |
WI2 802.11 protocols: | bgn |
WI2 MIMO config: | 3x3:3 |
ETH chip1: | Broadcom BCM4708A0 |
Switch: | Broadcom BCM4708A0 |
LAN ports: | 4x1G |
WAN ports: | 1x1G |
[edit] Installation
[edit] Prerequisites
**WARNING**: There was a period of time that there were specific factory-to-ddwrt.bin files required; this should be fixed in current releases. If flashing current release factory-to-ddwrt.bin files results in a boot loop or brick, please refer to the Recovery section below to enter Emergency Room to flash a known good file from here.
NOTE: 03-05-2020-r42617 is a known good initial flash build. See [1]
NOTE: See Where do I download firmware? for information on where to find firmware images.
- Download the factory-to-ddwrt.bin and dir880-webflash.bin files in the dlink-dir880l from the current release folder.
[edit] Flash from OEM factory firmware
[edit] Flash from D-Link Emergency Room
[edit] Upgrading DD-WRT
[edit] Prerequisites
NOTE: See Where do I download firmware? for information on where to find firmware images.
- Download the dir880-webflash.bin file in the dlink-dir880l from the current release folder.
[edit] Procedure
- Connect your computer to your router with an Ethernet cable.
- Enter http://192.168.1.1 (or whatever you set your router IP to) into a web browser.
- Enter username and password as required.
- Go to Administration -> Firmware Upgrade
- Leave Do Not Reset selected for After Flashing
- Click on Browse and select the dir880-webflash.bin file you previously downloaded.
- Click Open
- Click Upgrade
- The firmware update starts and the router restarts. The firmware update process takes about five minutes.
- If the webUI does not automatically go back to the Setup -> Basic Setup page, or does not stop at the progress bar page to allow you to click Continue after waiting at least five minutes (i.e. if you get a "Connection Reset" or other error page in your browser), enter http://192.168.1.1 (or whatever your router IP address is) manually or click and hold the "Back" button and select the appropriate history entry.
**CAUTION**: After you start the firmware update, do not try to go online, turn off the router, or do anything else to the router until it finishes restarting.
[edit] Recovery
D-Link Forums -> Emergency Flashing HOW-TO
[edit] Useful information, Further reading, Links
- D-Link DIR-880L (original thread to add device support)
- Flashing DIR-880L with DD-WRT (historical)