D-Link DIR-825

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 16:42, 19 December 2011 (edit)
DasShrubber (Talk | contribs)
m (Specifications)
← Previous diff
Revision as of 16:43, 19 December 2011 (edit) (undo)
DasShrubber (Talk | contribs)
m (Specifications)
Next diff →
Line 10: Line 10:
!RAM !RAM
|64 MB |64 MB
 +|-
!Flash !Flash
|8 MB |8 MB
 +|-
!Switch !Switch
|Realtek RTL8366SR |Realtek RTL8366SR
 +|-
!Radio (2.4 GHz) !Radio (2.4 GHz)
|AR9223 |AR9223
 +|-
!Radio (5 GHz) !Radio (5 GHz)
|AR9220 |AR9220
 +|-
!Antenna Type !Antenna Type
|External (Dual Band) |External (Dual Band)
 +|-
!Number Of Antennas !Number Of Antennas
|2 |2
 +|-
!Antenna Gain (2.4 GHz) !Antenna Gain (2.4 GHz)
|2 dBi |2 dBi
 +|-
!Antenna Gain (5 GHz) !Antenna Gain (5 GHz)
|2 dBi |2 dBi
 +|-
!Max TX Power (2.4 GHz) !Max TX Power (2.4 GHz)
|18dBm |18dBm
 +|-
!Max TX Power (5 GHz) !Max TX Power (5 GHz)
|17dBm |17dBm
 +|-
!Antenna Chains (TX/RX) !Antenna Chains (TX/RX)
|1+2/1+2 |1+2/1+2

Revision as of 16:43, 19 December 2011

Contents


Hardware

Specifications

CPU AR7161 680 MHz
RAM 64 MB
Flash 8 MB
Switch Realtek RTL8366SR
Radio (2.4 GHz) AR9223
Radio (5 GHz) AR9220
Antenna Type External (Dual Band)
Number Of Antennas 2
Antenna Gain (2.4 GHz) 2 dBi
Antenna Gain (5 GHz) 2 dBi
Max TX Power (2.4 GHz) 18dBm
Max TX Power (5 GHz) 17dBm
Antenna Chains (TX/RX) 1+2/1+2

Installation Instructions

Step-by-step instructions from out-of-the-box factory firmware

To install dd-wrt on a D-Link DIR-825 you can flash it directly from the router's web admin page (yes, that is correct... from D-Link's standard web interface). These are the steps to follow:

  1. Download the correct factory to ddwrt firmware for you router; NA (North America): [ ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2011/12-12-11-r18000/dlink-dir825-revb/factory-to-ddwrt_NA.bin R18000 NA], TW (Taiwan): [ ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2011/12-12-11-r18000/dlink-dir825-revb/factory-to-ddwrt_TW.bin R18000 TW], WW (World Wide, any place thats NOT in NA or TW): [ ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2011/12-12-11-r18000/dlink-dir825-revb/factory-to-ddwrt_WW.bin R18000 WW]
  2. Set your IPv4 network adapter to the following in your windows network configuration to: IP Address: 192.168.0.2, Subnet Mask: 255.255.255.0, Gateway: 192.168.0.1
  3. Physically connect the router ethernet port #1 to your computer ethernet port (NO WIRELESS!)
  4. Perform the 30/30/30 procedure:
    1. With power on, hold the reset button down for 30 seconds.
    2. Without releasing the reset button, unplug the router. Continue holding the reset button for 30 more seconds.
    3. Without releasing the reset button, plug the power back in and continue to hold the reset button for 30 more seconds.
    4. Release the reset button. The power light should be flashing on and off yellow.
  5. In Internet Explorer or Firefox enter http://192.168.0.1
  6. You should see a screen titled "Firmware Upgrade System".
  7. Select the “factory-to-ddwrt_XX.bin" file you downloaded and click the Send button to flash your router. As the firmware is uploaded and installed you will see the screen start counting to 100 percent. The power light will remain out during this process. At 100% the power light the power light will flash yellow and the router will reboot. The router globe will be yellow, the power will be blue, the 2.4/5GHz will be flashing blue.
  8. Remove the static IP from your computer network settings.
  9. Using Internet Explorer or Firefox go to: http://192.168.1.1 and You should see the DD-WRT screen to change your password.
  10. You should now be at the System Information screen.

How to upgrade with new DD-WRT firmware

  1. Download the latest firmware Upgrade-ddwrt R18000
  2. Open the DD-WRT's web interface in your web browser. It's http://192.168.1.1/ by default.
  3. Administration tab -> "Firmware Upgrade" button
  4. Click "browse" button -> select the "dir825-firmware.bin" file -> click "Upgrade" button. It will take about 2 minutes to upload and write the flash. Your browser will reload and let you know when it is done.
  5. It is probably a good idea to reboot after updating. That's it.

How to restore to factory firmware

  1. Download the stock firmware at ftp://ftp.dlink.com/Gateway/dir825_revB/Firmware/dir825_revB_FW_205NA.zip
  2. Set your IPv4 network adapter to the following in your windows network configuration to: IP Address: 192.168.0.2, Subnet Mask: 255.255.255.0, Gateway: 192.168.0.1
  3. Physically connect the router ethernet port #1 to your computer ethernet port (NO WIRELESS!)
  4. Perform the 30/30/30 procedure, using the same method you used to flash DD-WRT firmware.
  5. You should see the stock "Firmware Upgrade System" screen.
  6. Select the stock firmware that you downloaded in step 1 and click the Send button.
  7. Remove the static IP from your computer settings 1 minute after clicking send.
  8. Using Internet Explorer or Firefox go to: http://192.168.1.1 and You should see the DD-WRT screen to change your password.

Common Problems

  1. Dramatic reduction of WAN download speed over time.
    • Reboot temporarily clears the problem.
  2. Web GUI slows slowsmdown and becomes unresponsive over time.
    • Reboot temporarily clears the problem.

Supoport

External Links

Easy to follow and working guides for installing software on an external USB drive: http://g300nh.blogspot.com (start with software installation on dd-wrt part 1)