Buffalo WZR-HP-AG300H

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 18:27, 8 June 2011 (edit)
Buddee (Talk | contribs)
(Flashing instructions - finish up instructions, will add TFTP info later)
← Previous diff
Revision as of 08:39, 8 April 2012 (edit) (undo)
Buddee (Talk | contribs)
(add firmware info and links)
Next diff →
Line 63: Line 63:
9) Then, after you have waited atleast 3 minutes, re-log in the dd-wrt webgui @ http://192.168.1.1 and begin setup, enjoy dd-wrt! 9) Then, after you have waited atleast 3 minutes, re-log in the dd-wrt webgui @ http://192.168.1.1 and begin setup, enjoy dd-wrt!
 +
 +
 +== Firmware Versions ==
 +
 +To find the latest community DD-WRT builds for this unit you would need to browse the FTP and look for the appropriate build for your unit. Below is the link for the file server.
 +
 +ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/
 +
 +To find buffalo DD-WRT builds you would need to go to buffalo's support site and find the downloads section for your unit.
 +
 +http://www.buffalotech.com/products/wireless/routers-and-access-points/

Revision as of 08:39, 8 April 2012

This page is a WIP, please feel free to add useful infos


WZR-HP-AG300H Hardware Info

Image:wzr-hp-ag300h1.jpg Image:wzr-hp-ag300h2.jpg

CPU Atheros AR7161
CPU Speed 680 MHz
Flash ROM 32 MB
RAM 128 MB
Radios 1x 2.4 GHz / 1x 5Ghz
WLAN Support A/B/G/N
WLAN Max Speed 300 mbps
Antenna Location 2x fixed external
Switch 4x GigE + 1 WAN
USB 1x USB 2.0

Flashing instructions

This unit ships with the buffalo pro dd-wrt build 15940 pre-flashed onto the router. If you would like to use community builds for this unit (non-buffalo branded dd-wrt), then you will need to follow these steps to flash the community dd-wrt build onto the unit. And to note, this method will work for going from buffalo pro dd-wrt or buffalo user friendly firmware to community dd-wrt.

1) Download the community dd-wrt build for this model using the link below.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2011/04-09-11-r16785/buffalo_wzr-hp-ag300h/buffalo_to_ddwrt_webflash-MULTI.bin

2) Perform a reset on the router holding the reset button down for 30 seconds and then release.

3) Set a static IP on your PC to 192.168.11.2 and subnet 255.255.255.0, gateway 192.168.11.1

4) Log in the router's web-gui @ http://192.168.11.1 and go to the firmware upgrade section and select the file you downloaded in the first step.

5) After you selected the file from the first step, if you are in the buffalo dd-wrt pro build then select "reset to default settings" and click "upgrade"

6) Give this atleast 6 minutes to complete, do not unplug or mess with the unit in any form or fashion... BE PATIENT!

7) After you have waited, un-set the static ip of 192.168.11.2 and either set it to use DHCP or set a static ip of 192.168.1.8

8) Log in the dd-wrt webgui @ http://192.168.1.1 and once in, immediately go to Administration > Factory Defaults and select to "restore to factory defaults" again wait atleast 3 minutes. This will give it the equivalent of a hard reset to assure flash integrity.

9) Then, after you have waited atleast 3 minutes, re-log in the dd-wrt webgui @ http://192.168.1.1 and begin setup, enjoy dd-wrt!


Firmware Versions

To find the latest community DD-WRT builds for this unit you would need to browse the FTP and look for the appropriate build for your unit. Below is the link for the file server.

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/

To find buffalo DD-WRT builds you would need to go to buffalo's support site and find the downloads section for your unit.

http://www.buffalotech.com/products/wireless/routers-and-access-points/