From DD-WRT Wiki
(Difference between revisions)
Revision as of 14:54, 16 January 2006 (edit) 69.199.100.22 (Talk) ← Previous diff |
Current revision (18:13, 16 November 2017) (edit) (undo) Ian5142 (Talk | contribs)
|
(20 intermediate revisions not shown.) |
Line 1: |
Line 1: |
- | == Bridge Mode Install == | + | Depreciated, |
| | | |
- | I was having trouble getting OpenWRT to do any sort of bridging with my Belkin A/G ap, so I'm trying out bridge mode using DD-WRT. | + | * See [[Linking_Routers]] |
| | | |
- | Hardware: Linksys WRT54G V2 / Belkin A+G Dual Mode AP Router F6D3230-4 firmware 1.01.05 | + | [[Category:Switch]] |
- | | + | |
- | === Flashing from OpenWRT and getting to the GUI === | + | |
- | | + | |
- | I figured I'd give it a go to just use the 'upgrade firmware' link in OpenWRT to flash DD-WRT2.3-voip. | + | |
- | It worked, using a laptop and my Belkin A mode wlan connection. Once the flash was rolling, I did an | + | |
- | | + | |
- | ifconfig eth0 192.168.1.100 | + | |
- | | + | |
- | to bring up the laptop ethernet connection to the linksys. Then http://192.168.1.1 brought up the gui. | + | |
- | Now to figure out the default username and password. Ok, default username is blank. Default password is admin. | + | |
- | | + | |
- | === Configuration === | + | |
- | | + | |
- | My local network is 10.6.6.0/24, my belkin is at 10.6.6.1, ssid examplessid, channel 1, WPA-PSK, with a | + | |
- | 63 character passphrase. (The belkin does not allow a 64 hex key to be entered, only a passphrase.) | + | |
- | | + | |
- | ==== Setup ==== | + | |
- | | + | |
- | ===== Basic Setup ===== | + | |
- | | + | |
- | First page, Internet is disabled (I use another pc as a gateway connected to my cable modem). DHCP server is also disabled, I use static ips in my lan. | + | |
- | | + | |
- | *Assign WAN port to Switch - enabled | + | |
- | | + | |
- | ===== Advanced Routing ===== | + | |
- | | + | |
- | *Advanced Routing | + | |
- | **Operating Mode - Gateway | + | |
- | | + | |
- | ===== VLANS ===== | + | |
- | | + | |
- | I added the wan port interface (W) to the top line VLAN which should include it in the normal LAN. I don't use this AP as a NAT router, so I can use the WAN port as another LAN port. | + | |
- | | + | |
- | ==== Wireless ==== | + | |
- | | + | |
- | ===== Basic Settings ===== | + | |
- | | + | |
- | *'''Wireless Mode - Client Bridge''' | + | |
- | *Wireless Network Mode - Mixed | + | |
- | *Wireless Network Name (SSID) - examplessid | + | |
- | | + | |
- | ===== Wireless Security ===== | + | |
- | | + | |
- | *Security Mode - WPA2 Pre-Shared Key (The belkin calls it WPA but allows me to use AES, so from what I understand that would be WPA2 | + | |
- | *WPA Algorithms - TKIP+AES (I used AES on the Belkin but I'm unsure about the Group Key, so this can't hurt. | + | |
- | | + | |
- | ==== Security ==== | + | |
- | | + | |
- | ===== Firewall ===== | + | |
- | | + | |
- | *Firewall Protection - Disabled | + | |
- | | + | |
- | ==== Administration ==== | + | |
- | | + | |
- | ===== Management ===== | + | |
- | | + | |
- | *DNS Masq - Disable | + | |
- | *Local DNS - Disable | + | |
- | *802.1X - Disable | + | |
- | *NTP Client - Disable | + | |
- | | + | |
- | ===== Services ===== | + | |
- | | + | |
- | *SSHD - Enable (This probably should be the default) | + | |
- | *Telnet - Disable (This probably should be the default) | + | |
Current revision
Depreciated,