Bridge Install

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 06:32, 16 January 2006 (edit)
69.175.179.84 (Talk)

← Previous diff
Current revision (18:13, 16 November 2017) (edit) (undo)
Ian5142 (Talk | contribs)

 
(21 intermediate revisions not shown.)
Line 1: Line 1:
-== Bride Mode Install ==+Depreciated,
-I was having trouble getting OpenWRT to do any sort of bridging with my Belkin A/G ap, so I'm trying out bridge mode using DD-WRT. +* See [[Linking_Routers]]
-Hardware: Linksys WRT54G V2 / Belkin A+G Dual Mode AP Router F6D3230-4 firmware 1.01.05+[[Category:Switch]]
- +
-=== Flashing from OpenWRT and getting to the GUI ===+
- +
-I figured I'd give it a go to just use the 'upgrade firmware' link in OpenWRT to flash DD-WRT2.3-voip.+
-It worked, using a laptop and my Belkin A mode wlan connection. Once the flash was rolling, I did an +
- +
-ifconfig eth0 192.168.1.100+
- +
-to bring up the laptop ethernet connection to the linksys. Then http://192.168.1.1 brought up the gui.+
-Now to figure out the default username and password. Ok, default username is blank. Default password is admin.+
- +
-=== Configuration ===+
- +
-My local network is 10.6.6.0/24, my belkin is at 10.6.6.1, ssid examplessid, channel 1, WPA-PSK, with a+
-63 character passphrase. (The belkin does not allow a 64 hex key to be entered, only a passphrase.) +
- +
-==== Setup ====+
- +
-===== Basic Setup =====+
- +
-First page, Internet is disabled (I use another pc as a gateway connected to my cable modem). DHCP server is also disabled, I use static ips in my lan.+
- +
-*Assign WAN port to Switch - enabled+
- +
-===== Advanced Routing =====+
- +
-*Advanced Routing+
-**Operating Mode - Gateway+
- +
-===== VLANS =====+
- +
-I added the wan port interface (W) to the top line VLAN which should include it in the normal LAN. I don't use this AP as a NAT router, so I can use the WAN port as another LAN port.+
- +
-==== Wireless ====+
- +
-===== Basic Settings =====+
- +
-*'''Wireless Mode - Client Bridge'''+
-*Wireless Network Mode - Mixed+
-*Wireless Network Name (SSID) - examplessid+
- +
-===== Wireless Security =====+
- +
-*Security Mode - WPA2 Pre-Shared Key (The belkin calls it WPA but allows me to use AES, so from what I understand that would be WPA2+
-*WPA Algorithms - TKIP+AES (I used AES on the Belkin but I'm unsure about the Group Key, so this can't hurt.+
- +
-==== Security ====+
- +
-===== Firewall =====+
- +
-*Firewall Protection - Disabled+
- +
-==== Administration ====+
- +
-===== Management =====+
- +
-*DNS Masq - Disable+
-*Local DNS - Disable+
-*802.1X - Disable+
-*NTP Client - Disable+
- +
-===== Services =====+
- +
-*SSHD - Enable (This probably should be the default)+
-*Telnet - Disable (This probably should be the default)+

Current revision

Depreciated,