Belkin Share Max N300 F7D7301 F7D3301

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 05:34, 3 September 2016 (edit)
Skygunner (Talk | contribs)
(New page: Initial flash and CFE recovery how to http://tsengf.blogspot.com/2012/05/dd-wrt-on-belkin-share-max-n300.html Note: This router has gigabit switch; DD-WRT Mini build doesn't have the driv...)
← Previous diff
Current revision (17:06, 25 February 2018) (edit) (undo)
Ian5142 (Talk | contribs)
(Changes to hardware table.)
 
(4 intermediate revisions not shown.)
Line 1: Line 1:
 +{{Languages|Belkin Share Max N300 F7D7301 F7D3301}}
 +__TOC__
 +
 +==Introduction==
 +
 +
 +{| border="1" cellspacing="0"
 +! CPU
 +| Broadcom BCM4718A1
 +|-
 +! CPU instruction set
 +| MIPS 74K V4.0
 +|-
 +! Flash ROM
 +| 8 MB<br>Eon EN29LV640B
 +|-
 +! RAM
 +| 64 MB
 +|-
 +! Radios
 +| 2.4 GHz
 +|-
 +! WLAN Support
 +| a/b/g/n
 +|-
 +! WLAN Max Speed
 +| 300mbps (2.4 GHz)
 +|-
 +! Antenna Location
 +| Internal (x2)
 +|-
 +! MIMO Config
 +| 2x2:2
 +|-
 +! Radio wl0
 +| Broadcom 4718 (SoC)
 +|-
 +|-
 +! Switch
 +| 4x GigE + 1 WAN<br>Broadcom 53115<br>IEEE 802.3/3u/3ab
 +|-
 +! USB
 +| 2x USB 2.0
 +|}
 +
 +=Installation=
Initial flash and CFE recovery how to Initial flash and CFE recovery how to
http://tsengf.blogspot.com/2012/05/dd-wrt-on-belkin-share-max-n300.html http://tsengf.blogspot.com/2012/05/dd-wrt-on-belkin-share-max-n300.html
Line 4: Line 50:
Note: Note:
This router has gigabit switch; This router has gigabit switch;
-DD-WRT Mini build doesn't have the driver for gigabit switch; 
So if you do the initial flash using F7D7301-mini build or F7D3301-mini build, after flashing So if you do the initial flash using F7D7301-mini build or F7D3301-mini build, after flashing
Line 10: Line 55:
You won't have ip assigned from the router if connected wired. You won't have ip assigned from the router if connected wired.
You can't ping the router even you assign a static IP address for the wired connection. You can't ping the router even you assign a static IP address for the wired connection.
-At this point, upgrade the mini build to some larger build like VPN or Mega build, then the wired switch will work as should.+At this point, upgrade the mini build to some larger build like VPN or Mega build, then the wired switch will work as should. Make sure the build is less than '''8 000 000''' bytes or you will brick the router. See [[Index:FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] for links.
- +
-system type : Broadcom BCM4716 chip rev 1+
-processor : 0+
-cpu model : MIPS 74K V4.0+
-BogoMIPS : 226.09 (Linksys_WRT1900AC_v2 3188.32, MTK7620A 385.02)+
-wait instruction : no+
-microsecond timers : yes+
-tlb_entries : 64+
-extra interrupt vector : no+
-hardware watchpoint : yes+
-ASEs implemented : mips16 dsp+
-shadow register sets : 1+
-with DD-WRT K26+[[Category:Belkin guides]]
-Router Model+
-Belkin F7D3301 / F7D7301 v1+
-Firmware Version DD-WRT v3.0-r30534 mega (09/01/16)+
-Kernel VersionLinux 2.6.24.111 #30935 Thu Sep 1 08:44:53 CEST 2016 mips+
-NVRAM 26 KB / 32 KB+

Current revision

Contents


[edit] Introduction

CPU Broadcom BCM4718A1
CPU instruction set MIPS 74K V4.0
Flash ROM 8 MB
Eon EN29LV640B
RAM 64 MB
Radios 2.4 GHz
WLAN Support a/b/g/n
WLAN Max Speed 300mbps (2.4 GHz)
Antenna Location Internal (x2)
MIMO Config 2x2:2
Radio wl0 Broadcom 4718 (SoC)
Switch 4x GigE + 1 WAN
Broadcom 53115
IEEE 802.3/3u/3ab
USB 2x USB 2.0

[edit] Installation

Initial flash and CFE recovery how to http://tsengf.blogspot.com/2012/05/dd-wrt-on-belkin-share-max-n300.html

Note: This router has gigabit switch;

So if you do the initial flash using F7D7301-mini build or F7D3301-mini build, after flashing you want have wired network to the router, you only have wireless access to the router. You won't have ip assigned from the router if connected wired. You can't ping the router even you assign a static IP address for the wired connection. At this point, upgrade the mini build to some larger build like VPN or Mega build, then the wired switch will work as should. Make sure the build is less than 8 000 000 bytes or you will brick the router. See Where do I download firmware? for links.