Asus RT-N15
From DD-WRT Wiki
Contents |
NOTE: This device is a WIP.
NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.
Specs
This section is in need of cleanup!
Platform
Serial Num. = ? FCC ID = MSQ-RTN15 CPU Type = Ralink RT2880F GV76440C0 0740ST MIPS Rev = ? CPU Speed = 266MHz Bus = ? Flash Type = Parallel Flash Chip = MX T072421 29LV320CBT 2U761500A1 Flash Size = 4MB RAM Size = 32MB (2x 16MB) RAM Chip = Samsung 743 K4S281632K-UCG0 nvram Size = ? Switch = Ralink RTL8366SR 7A085S2 G742B Port-based vlan = ? 802.1q vlan = ? Ethernet Port Count = 1-10/100/1000-WAN 4-10/100/1000-LAN Wired Standard = ? boot_wait = ? CF Card Socket = No SD/MMC Mod Support = No MiniPCI slots = No PoE = No Power = 5V/2.5A Color of LEDs = ? USB = No Serial Port = 1 JTAG Port = No Supported by TJTAG 3.02 = ? Supported by dd-wrt as of = WIP as of 16019 dd-wrt K2.4 Support = No dd-wrt K2.6 Support = Yes Special Features = Gigabit Switch
Radio
Wireless Radio = Ralink RT2820L CV13930B 07125T WLAN DSP processor = ? Antenna Connector Type = Internal Wireless Standard = b/g/n WiFi Operating Frequency = 2.4GHz ~ 2.5GHz 802.11n Draft = up to 300Mbps 802.11g = 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b = 1, 2, 5.5, 11Mbps Radio cor_rev = ? Radio Capabilities = ?
Threads of interest
Flashing
The device is stitched from windows Firmware update in an official insertion (the version of an insertion 1.0.0.7)
File - factory-to-ddwrt.trx or File factory-to-ddwrt.trx
Upgrading
This section is in need of cleanup!
Reverting
For reset it is necessary to translate the device to an original insertion in a recovery mode. 1. We install program Restoration Firmware. 2. We drop device adjustments. 3. We disconnect the device. 4. We push the button ресет and we include a supply, without releasing the button ресет, we wait when the power indicator will start blinking, we release the button ресет. 5. We launch program Restoration Firmware, we select a file with an insertion, we stitch. 6. After a reinsertion we come into a router and we drop adjustments on the factory. We ungear the device. 7. We include a router and it is provisionable.
JTAG/Serial Info
JTAG
This router does not have JTAG.
Serial
Serial Pinouts
This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - Communication - HyperTerminal Enter a name for the connection, Click ok Choose com port you adapter is plugged into, Click ok Set: Bits per second = 115200 Data Bits = 8 Parity = none Stop bits = 1 Flow control = none Click ok Click File - Save As, and select a place to save it to so you don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Serial Recovery
This section is in need of Serial Recovery Instructions!