Asus RT-N15

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 15:06, 25 May 2018 (edit)
Ian5142 (Talk | contribs)
(Added link to Where do I download firmware.)
← Previous diff
Revision as of 15:18, 25 May 2018 (edit) (undo)
Ian5142 (Talk | contribs)
(Updated revert section, reworded. Unsure about some of it.)
Next diff →
Line 22: Line 22:
==Reverting== ==Reverting==
-For reset it is necessary to translate the device to an original insertion in a recovery mode. +To restore the device to factory firmware, you need to put it in Recovery Mode.
-1. We install program Restoration Firmware.+# Download the factory firmware
-2. We drop device adjustments.+# In dd-wrt, reset to factory defaults, through the GUI or CLI.
-3. We disconnect the device.+# Disconnect everything from the router, except the power cord.
-4. We push the button ресет and we include a supply, without releasing the button ресет, we wait when the power indicator will start blinking, we release the button ресет. +# Push and hold the Reset button with the router powered on. Without releasing the Reset button, unplug the router.
-5. We launch program Restoration Firmware, we select a file with an insertion, we stitch.+# Wait until the power light starts blinking, then release the Reset button.
-6. After a reinsertion we come into a router and we drop adjustments on the factory. We ungear the device.+# (Not tested, most likely access a webpage at 192.168.0.1 or 192.168.1.1) We launch program Restoration Firmware, we select a file with an insertion, we stitch.
-7. We include a router and it is provisionable.+# (Not tested) Browse to the factory firmware file. Click the Upload button.
 +# (Not tested) Wait at least 5 minutes before touching the power cord.
 +# (Not tested) Do a factory reset once the router comes back up successfully.
==JTAG/Serial Info== ==JTAG/Serial Info==

Revision as of 15:18, 25 May 2018

Contents

NOTE: This device is a WIP.
NOTE: Requires K2.6, Do not flash anything else.
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Specs

See wikidevi page for full specs: https://wikidevi.com/wiki/ASUS_RT-N15

Threads of interest

Flashing

The device is stitched from windows Firmware update in an official insertion (the version of an insertion 1.0.0.7)

Firmware files can be found here: Where do I download firmware? (asus-rt-n15 folder). Use the factory-to-ddwrt.trx to flash from Factory firmware to dd-wrt.

Upgrading

Firmware files can be found here: Where do I download firmware? (asus-rt-n15 folder). Use the asus-rt-n15-ddwrt-webflash.bin file to upgrade dd-wrt to a newer version.

Reverting

To restore the device to factory firmware, you need to put it in Recovery Mode.

  1. Download the factory firmware
  2. In dd-wrt, reset to factory defaults, through the GUI or CLI.
  3. Disconnect everything from the router, except the power cord.
  4. Push and hold the Reset button with the router powered on. Without releasing the Reset button, unplug the router.
  5. Wait until the power light starts blinking, then release the Reset button.
  6. (Not tested, most likely access a webpage at 192.168.0.1 or 192.168.1.1) We launch program Restoration Firmware, we select a file with an insertion, we stitch.
  7. (Not tested) Browse to the factory firmware file. Click the Upload button.
  8. (Not tested) Wait at least 5 minutes before touching the power cord.
  9. (Not tested) Do a factory reset once the router comes back up successfully.

JTAG/Serial Info

JTAG

This router does not have JTAG.

Serial

Serial Pinouts
This section is in need of cleanup!
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - 
   Communication - HyperTerminal
Enter a name for the connection, Click ok
Choose com port you adapter is plugged into, Click ok
Set:
 Bits per second = 115200
 Data Bits = 8
 Parity = none
 Stop bits = 1
 Flow control = none
Click ok
Click File - Save As, and select a place to save it to so you 
             don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it
 Serial line = The COM port your using for serial (ie. COM3)
 Speed = 115200
Click on Serial under Connection
 Serial line to connect to = same as above (Serial line)
 Speed (baud) = 115200
 Data bits = 8
 Stop bits = 1
 Parity = None
 Flow control = None
Click Session
 Enter a name for your connection under saved sessions
Click Save
Click Open
Serial Recovery
This section is in need of Serial Recovery Instructions!

Notes