Alfa N5
From DD-WRT Wiki
Revision as of 13:42, 22 June 2014 (edit) Sash (Talk | contribs) (→U-Boot) ← Previous diff |
Current revision (15:01, 2 April 2018) (edit) (undo) Ian5142 (Talk | contribs) (Added link to Where do I download firmware.) |
||
(6 intermediate revisions not shown.) | |||
Line 1: | Line 1: | ||
__TOC__ | __TOC__ | ||
- | '''= Planet WNAP-7320''' | + | '''= Planet WNAP-7320 = OTAi 724S''' |
+ | |||
+ | This instruction is also valid for the '''Alfa N5c''' | ||
=Hardware= | =Hardware= | ||
*CPU Atheros AR7240 | *CPU Atheros AR7240 | ||
- | *Flash 8MB | + | *Flash 8MB |
- | *RAM 32 MB | + | *RAM 32 MB |
- | + | ||
==Serial Port== | ==Serial Port== | ||
Line 23: | Line 24: | ||
==Initial== | ==Initial== | ||
For initial flashing you have to access the device via serial connection. | For initial flashing you have to access the device via serial connection. | ||
+ | |||
+ | Firmware files can be found here: [[Index:FAQ#Where_do_I_download_firmware.3F|Where do I download firmware?]] | ||
+ | |||
===U-Boot=== | ===U-Boot=== | ||
Since the default is set to boot from the fixed address 0x9f650000, an new bootloader must be flashed before you can boot DD-WRT. | Since the default is set to boot from the fixed address 0x9f650000, an new bootloader must be flashed before you can boot DD-WRT. | ||
+ | You will have to setup an tftp server where you can download the files. When the cli asks type 1 to enter the command line. print the envsettings and set the ip and server address. | ||
Process each line step by step from the uboot console: | Process each line step by step from the uboot console: | ||
Line 31: | Line 36: | ||
cp.b $fileaddr 0x9f000000 $filesize | cp.b $fileaddr 0x9f000000 $filesize | ||
- | + | when the download doesnt work, try again with the 2nd eth port. | |
+ | The new version will be U-Boot 1.1.4 <br> | ||
+ | '''Dont reset/reboot yet!''' | ||
===DD-WRT/Recovery=== | ===DD-WRT/Recovery=== |
Current revision
Contents |
= Planet WNAP-7320 = OTAi 724S
This instruction is also valid for the Alfa N5c
[edit] Hardware
- CPU Atheros AR7240
- Flash 8MB
- RAM 32 MB
[edit] Serial Port
115000,1,n,8
1 PWR 2 TX 3 RX 4 GND
[edit] Flashing
[edit] Initial
For initial flashing you have to access the device via serial connection.
Firmware files can be found here: Where do I download firmware?
[edit] U-Boot
Since the default is set to boot from the fixed address 0x9f650000, an new bootloader must be flashed before you can boot DD-WRT. You will have to setup an tftp server where you can download the files. When the cli asks type 1 to enter the command line. print the envsettings and set the ip and server address. Process each line step by step from the uboot console:
tftpboot 0x80060000 uboot.bin erase 9f000000 +$filesize cp.b $fileaddr 0x9f000000 $filesize
when the download doesnt work, try again with the 2nd eth port.
The new version will be U-Boot 1.1.4
Dont reset/reboot yet!
[edit] DD-WRT/Recovery
Afer the uboot is flashed go on installing DD-WRT from the cli:
tftp 0x80060000 firmware.bin erase 9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize