刷新您的Buffalo WBR-G54,WLA-G54,WBR2-G54,WBR2-G54S...

From DD-WRT Wiki

Revision as of 20:54, 10 January 2007 by 1168461722 (Talk | contribs)
Jump to: navigation, search

... WLA-G54C, WBR2-G54, WBR2-G54S

WARNING: Use only dd-wrt v23 final (25.dec.2005) or v23 SP1 final (16.may.2006). Some beta versions are buggy and will brick your router.

WARNING: The WAN port and LAN ports could be temporarily swapped

WARNING: Some routers' status lights (LEDs) will not work

WARNING: Reset button will not work

WARNING: Currently no way to go back to original firmware (I did it once, but could not reproduce)


1) Flashing using TFTP [Suggested Method]

Before flashing be sure to restore to factory defaults. Also check if you can connect to the router wirelessly.

Follow directions under Installation#Flashing_the_Buffalo_WHR-G54S_and_WHR-HP-G54

Note for WBR2-G54 users: Users have reported that once they install DD-Wrt, they have been unable to restore the original Buffalo 2.30 firmware (even via tftp after removing the first 35 bytes). A few users have reported success with a later version of Buffalo firmware, 2.32, that they obtained through Buffalo Tech Support; they were able to tftp this 2.32 version, after they had adjusted the header as shown below.


2) Flashing using Buffalo's WEB interface [Alternate Method]

Use the DD-WRT generic version with the added Buffalo header. After successful transfer please wait 2-3 min., or until router reboots.


Inspecting the original Buffalo firmware one can see the custom header (before HDR0).

WBR-G54, WBR-B11 (34 bytes)

00h:  57 42 52 2D 42 31 31 20 32 2E 32 30 20 31 2E 31 ; WBR-B11 2.20 1.1
01h:  36 0A 66 69 6C 65 6C 65 6E 3D 33 32 31 39 34 35 ; 6.filelen=321945
02h:  36 0A                                           ; 6.

WLA-G54 (34 bytes)

00h:  57 4C 41 2D 47 35 34 20 32 2E 30 35 20 31 2E 30 ; WLA-G54 2.05 1.0
01h:  32 0A 66 69 6C 65 6C 65 6E 3D 32 35 34 37 37 31 ; 2.filelen=254771
02h:  32 0A                                           ; 2.

WLA-G54C (35 bytes)

00h:  57 4C 41 2D 42 31 31 43 20 32 2E 32 30 20 31 2E ; WLA-B11C 2.20 1.
01h:  30 35 0A 66 69 6C 65 6C 65 6E 3D 32 37 31 31 35 ; 05.filelen=27115
02h:  35 32 0A                                        ; 52.

WBR2-G54 (35 bytes)

00h:  57 42 52 32 2D 47 35 34 20 32 2E 33 30 20 36 2E ; WBR2-G54 2.30 6.
01h:  30 33 0A 66 69 6C 65 6C 65 6E 3D 33 35 35 39 34 ; 03.filelen=35594
02h:  32 34 0A                                        ; 24.

WBR2-G54S (36 bytes)

00h:  57 42 52 32 2D 47 35 34 53 20 32 2E 33 30 20 36 ; WBR2-G54S 2.30 6
01h:  2E 31 30 0A 66 69 6C 65 6C 65 6E 3D 33 35 32 36 ; .10.filelen=3526
02h:  36 35 36 0A                                     ; 656.


You will need to insert (prepend) these bytes onto the DD-WRT generic firmware if you want to flash using Buffalo's WEB interface. You generally need to adjust the "filelen=" number to reflect the size of DD-WRT (though it may work without these "filelen=" adjustments).


3) Buffalo's default IP address: 192.168.11.1. Router will also listen to this address during boot. It will answer to pings with TTL=128. (DD-WRT answers with TTL=64)

Buffalo WBR2-G54/WBR2-G54S users: Remember to set the IP address to 192.168.1.1 before continuing. These white soap boxes' hardware use this IP address in their bootloader. If you have trouble, flash it first with Generic DD-WRT -firmware, turn off after first boot, and after plugging the power cord back in, wait 2 seconds, press Reset-button, let it enter troubleshoot mode (couple minutes), then power off second time, and power back on and it should work. Note: Do not turn on device while holding the Reset-button, since that might signal the bootloader to erase some vital configurations which are known only inside Buffalo Tech. Just wait 2 seconds and then start holding the button, this signals the WRT firmware to use troubleshoot-mode and it kind of repairs the NVRAM... (worked for me, Esa Häkkinen 2006-02-02 <esa.hakkinen@evtek.fi>)


4) After flash:

You will be able to access the router at 192.168.11.1. Do not restore to factory defaults, but you can erase the nvram. Telnet to the router (username: root , password: admin , mtd erase nvram [enter], reboot [enter].

Please note: If you do restore to factory defaults, the router will respond at 192.168.1.1. Maybe you will no longer be able to access the router via LAN ports. Try using the WAN port, or through the wireless connection (ssid = linksys, ch.6, no encryption). Once you are connected, please telnet to the router and erase nvram (username: root , password: admin , mtd erase nvram [enter], reboot [enter]. This will bring back the LAN ports at 192.168.11.1.

Please note: Clearing nvram will also change the MAC addresses from 00:07:40:xx:xx:xx (Melco Inc.) to 00:90:4c:xx:xx:xx (Epigram Inc.). If you need original MACs back, telnet to the router and do the following: (Use LAN MAC address from the label from router's back side)

nvram set et0macaddr=xx:xx:xx:xx:xx:xx
nvram commit
reboot

You can also clone WAN and WLAN MACs using the GUI interface ("Setup"->"MAC Address Clone")

You can now enjoy your DD-WRT....


5) Upgrading to new DD-WRT version

Once the router runs DD-WRT, please use the generic version when upgrading firmware. (Starts with HDR0, i.e. dd-wrt.v23_generic.bin).


last revision: 14.june.2006










[l_sp_24]

aciphex 20mg Deltasone buy amaryl actos met plus adalat xl adalat cc altace and hair thinning arava side effects atarax hydroxyzine

beach flower sympathy mlm local lead chicago sympathy flower affiliate lead marketing mlm network mlm lead generation art clip flower sympathy mlm lead generation company generation lead site web mlm lead generation network marketing mlm software free sample mlm lead free mlm lead generation 1,000 free lead mlm 1000 free lead mlm sympathy flower toronto mlm lead generation online generation lead mlm program generation lead real time mlm buy flower funeral sympathy uk generation in lead mlm real time generation lead marketing mlm network flower ontario sympathy everyday free lead mlm targeted mlm lead opt in mlm email lead mlm opt in lead opt in mlm lead opt mlm lead flor carpet tile milliken carpet carpet cleaning franchise chem dry carpet cleaning mohawk carpet berber carpet dalton carpet miele vacuum cleaner electrolux vacuum cleaner ultrasonic cleaner kirby vacuum cleaner ultrasonic jewelry cleaner grout cleaner hardwood floor cleaner upholstery cleaner hoover steam cleaner exclusive mlm lead 20 generation lead marketing mlm network wild flower triathlon email free in lead mlm opt generation mlm lead custom business free lead mlm opportunity seeker capture free lead mlm affiliate free lead lead marketing mlm network nutrition business opportunity seeker mlm lead capture free lead mlm system flower from made silk sympathy wreath mlm genealogy lead ikebana flower arrangement flower hibiscus picture tattoo double opt in mlm lead flower mississauga sympathy generating guerilla lead marketing mlm program etobicoke flower sympathy