Linksys WRT54G v2.0
From DD-WRT Wiki
[edit] Flashing
NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.
- Read the Peacock announcement
- Do a hard reset on the router
- Set a static IP on your computer (e.g. 192.168.1.7, subnet mask 255.255.255.0)
- Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
- Power cycle the router (unplug the power from the router for 30 seconds and then plug it back in)
- Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the Linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
- Leave the username blank and enter "admin" as the password
- Go to administration and firmware upgrade
- Navigate to the folder that you are using, and select 14929 dd-wrt.v24_mini_wrt54g.bin
- Hit upgrade
- When you get a message that the upgrade is successful, wait FIVE FULL minutes before continuing.
- If you don't get success, repeat from steps 6 up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
- When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
- When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another HARD reset on the router.
- At this point you can choose to put a different build on, depending on what you needs are.
- Initially I used the version as indicated above, but it was unstable. My ISP provides a download speed of 22 MB, but after a few days, I could not get more than 2 MB. Restarting the router solved this. After I installed a *vintage* build, my router is running stable. Use the VINT version recommended in the peacock announcement.
- Reset your computer ethernet connection to auto IP and auto DNS
[edit] Corerev
Confirmed from diagnostics that wl0_correv > 5 by typing in the Admin->Commands window "nvram get wl0_corerev" which returned "7". This means the standard build should be used. redhawk
[edit] Other Notes
Comment Bualdoot on 12-Dec-2008: The comments below are from before I added the install instructions above. The comment below was refering to a comment that i removed, because it talked about not being sure if the WRT54Gv2 had more than 2MB memory, which of course we know it does. As for the instructions it gave that he refers to, they were not very clear, so, I made my own set of instructions based off the v1-v1.1 instructions.
all set [Comment from jas3 on 16-Mar-2008: The above worked for me. I then updated from standard to dd-wrt.v23_vpn_generic.bin which succeeded as well] May08, When upgrading to v24, please do a full firmware reset (hold reset button for 30 seconds on power up). I did not do this when upgrading to v24 and was getting all sorts of strange behaviors from my router. After resetting and then reconfiguring the router, all was well.
Comment MoT 11:01, 2 Jul 2007 (CEST) : I have been able to flash the VPN version on my V2.0, after flashing from the original Linksys firmware to the mini version first. I followed the V4 tutorial.
After flashing to the mini version, I couldn't flash to the VPN version at first, as I was immediately redirected to a blank page when trying to flash. This seemed to be a problem with IE7, with Firefox, it went fine.
Comment I Use Dial 13:54, 21 Jul 2007 (PDT) I installed mini to my v2.2 through Linksys GUI and had forgotten to reset factory defaults before uploading. I had same problem with blank screen loading but Firefox didn't help. Unplugged it, did a hard reset, unplugged it again, and everything was fine. Then uploaded latest stable version without issue.
Comment Glc 19:00, 31 October 2007 (CET) v2.0 Installed mini generic over Linksys firmware using the web interface, followed by standard generic with web interface. Setting to PPPoE knocked out the WAN port, worked fine in DHCP. Flashed back to mini generic and everything works as advertised.
Comment : Installed mini, then standard generic. No problems except I can't overclock. I try 216 but when applying and restarting all router lights flash together periodically every few seconds. Hard resetting using button takes router back to factory settings and then it works fine. Tried twice on v23 sp2 and once on v24 RC5.
Comment (March 19, 2008) : Just installed dd-wrt on my WRT54G v2 router. I started by installing wrt54gv2 v24 rc6.2 mini through the Linksys web interface and then after I got that installed I used the new dd-wrt mini interface to install wrt54gv2 v24rc6.2 standard generic. Everything is running smothly and I had no problems in getting dd-wrt installed.
Comment Doppelbock 22:15, 18 April 2008 (PDT) I just installed v23 SP2 full version (generic) on a WRT54G v2.2 that I bought used on eBay and don't seem to have any issues. I had to do a 30-second reset to log into the dd-wrt gui in IE but other than that it's been smooth sailing so far.
Comment Djmoore 11:02, 21 June 2008 (CEST) Installed v24-9517_VINT_mini on WRT54G 2.2 using Firefox 3 running on Linux/Ubuntu 8.04 with no problems. 30-30-30 reset before and after.
Comment Erocku June 2008: I was able to install the v24-9517_VINT_mini on my WRT54G v2.0. After the install I was then able to install the v24-9517_VINT_std with no problems. I was even able to do it from Safari.
Comment jcp_rev August 2008: I Installed two days ago dd-wrt.v24_vpn_generic.bin on my WRT54G v2.0. previous version dd-wrt.v23_mini_generic.bin. I did it from Firefox 3. using the standard procedure.
Comment --Dlfretz 18:05, 29 August 2008 (CEST)I was able to install the standard version after flashing the mini version. I just couldn't go straight to the standard version. I installed with Firefox 3.0 on Windows. This is an original Linksys WRT-54G version 2.0
Comment: 28 Sept 08 Uploaded v24sp1-micro generic on a v.2.0 - now I can't upload anything else. Have tried the VINt and the mega-generic and while the upload and reboot appear to be successful, the router still reports the micro version and features are unchanged.
Comment - skaterkfbs - Followed these instructions for a v2.2 and worked perfectly. I had trouble trying to go directly from LinkSys v4.21.1 firmware to DD-WRT v24 VINT Standard. Had to use the middle DD-WRT v24 VINT Mini.
Comment paillassou April 2009: My WRT54Gv2.0 [serial#CDF5*****] had an old (but fun too) FIRMWARE [FW = "v4.71.1 Hyperwrt 2.1b1 + Thibor15c"]. I would change for DD-WRT fw. So, after a hard reset 30/30/30 on the thibor15c's fw, i was able to flash successfully, the "mini version" DD-WRT fw through the WEB interface of the thibor15c's fw. I was able to install, 1st, the v24-9517_VINT_mini on my WRT54G v2.0. Reboot OK - DDWRTmini works fine => hard reset 30/30/30. After that, I was then able to install the v24-9517_VINT_std with no problems. Reboot OK - DDWRTstd works fine => hard reset 30/30/30. I was even able to do it from IE7. Install = FREEBOXv4 + WRT54Gv2.0 with FW=DD-WRTv24-9517_VINT_std. All is right. Thanks a lot for the tutorial and informations ;o)
Comment atlasit July 2009: After installing the mini firmware to a WRT54G v2.0 using IE8, clicked the Continue button and did a hard reset. The screen that comes up after the reset prompts to change the user and password of the router. It would not continue after clicking the button until I viewed the page in 'Compatibility Mode'. Then it took the changes.
Comment --Educmale 06:07, 11 November 2009 (CET): With Ver2.2, I noticed that both the VINT-std and the STD versions install and work fine, almost ---- the STD version won't allow a virtual wireless LAN to connect using WPA2-pers security, while operating in repeater mode. It acts like there is a bug there, in the STD version, in that virtual area -- Odd, as the STD version -will- connect as a wireless access point, using the same WPA2-pers setup. In contrast, VINT will allow the same set up to let the WPA2-pers function either as an AP or a virtual wireless Lan. [The STD version was the one available 3days ago; perhaps this bug will be fixed, one day?]
Comment --GNUton 12:37, 15 November 2010 (CET): Today I bricked my WRT54G 2.0 installing dd-wrt through the linksys web interface. I tried to install the generic mini firmware using Chromium 7.0 on Ubuntu. It uploaded fine the image on the router but at the end it showed an error message.