Linksys WRT320N v1.0
From DD-WRT Wiki
Contents |
[edit] WRT320N Information
Linksys WRT320N is supported since build 12956 (2009-09-23), using kernel 2.6. Device forum thread, for more information: Eko's original announcement
[edit] Hardware Specs
- CPU Broadcom BCM4717A (354 MHz)
- corerev: wl0=17
- Flash/RAM: 8MB (serial) / 32MB
- Radio: b/g/n 2.4 GHz OR a/n 5 GHz (Not dual radio)
- Wireless speed: up to 300 Mb/s
- Wireless MIMO config: 2x2:2
- Antenna gain: 1st and 2nd main 1.5 dbi, 3rd antenna: 2.2 dBi
- Ethernet: Broadcom BCM4717A
- Switch: Broadcom BCM53115
- WAN/LAN: 4 / 1 (Gigabit ethernet)
- S/N prefix: CUH0
WARNING: Linksys wired the reset button to the wrong gpio, so hard reset doesn't work, and boot_wait is off by default. In DD-WRT, the reset button works, and boot_wait is enabled. Builds after 13493 must be used for WPS button hard reset support, reference "30-30-30 reset does not work" for more info regarding how to hard reset this unit.
[edit] Installation instructions
- For initial flash, a trailed build (with the model in the file name) is required: 14929 K2.6 mini trailed build
- After initial flash, upgrades can use any non-trailed generic (not nv60k nor nv64k) K2.6 builds from HERE.
- Download the trailed build (K2.6_mini_wrt320n.bin), then from the Linksys webgui, reset to defaults.
- Router default address is 192.168.1.1: Set your pc to a static IP e.g. 192.168.1.6 subnet 255.255.255.0
- In the Linksys webgui, go to Upgrade and flash the trailed build, then wait' 5 minutes
- Open 192.168.1.1 to the DD-WRT GUI, set a user and password, then do a hard reset:
- Unplug the router, push and hold the WPS button on the front
- Plug the router back in, continuing to hold the button for 10-12 seconds, then release
- This should reset to defaults again: access the GUI to set a user and password, then set up DD-WRT
- Switch your PC back to DHCP if needed
[edit] Updates
Flash any generic (not nv60k nor nv64k) K2.6 (or K3.x) build under 7995392 bytes (7808 KB)
- The WRT320N trailed build can be used, but is unnecessary when already running DD-WRT
- For build type info, see here
- K3X builds have software expanded nvram, so is a workaround versus converting to an E2000
- SFE accelerated NAT was added since 33006 in k3.10+ (k3x is k3.10), useful for a main (gateway) router
- Repeater Bridge with WPA2-AES is broken for k2.6 builds after 25974, though some models might work through 26125
- The krack fix (affects client/repeater modes) is in all kernels
- For download links and other info see the Firmware FAQ
[edit] VLAN Support
The VLAN GUI was fixed since build 15508, but may not work for some configurations. For details, see the Switched Ports for manual configuration of the nvram variables.
[edit] Known issues with the WRT320N
[edit] 30-30-30 reset does not work
Linksys wired the reset button to the wrong GPIO, hence a 30-30-30 reset will not work.
In order to perform a hard reset on the WRT320N, follow these steps (using at least build 13493):
- Unplug router
- Press and hold the WPS button on the front of the unit.
- Plug power back in with button still pressed, hold down button for 10-12 seconds.
- Release button after 10-12 seconds. Wait 2 minutes, then access webgui at 192.168.1.1
You can also perform a hard reset by telnet or ssh by entering the following commands into the CLI.
erase nvram && reboot
[edit] Troubleshooting tips
Reference: install post by bbb_forever Router is not getting its WAN and DNS IP addresses from the ISP: -Cycle power on the modem to reset the DHCP lease
If you lose Internet access, but used to have it with the old router, then this may a possible remedy: -Clone the MAC Address of the previously working device e.g.:
- Local computer's MAC address or previous router's WAN MAC address (look on the bottom of the router)
-Worst case, you may have to call the ISP to reset the allowed MAC address
[edit] Some other useful tips
This router, and the newer E2000, use the Broadcom 4717 CPU. Broadcom uses a default clock of 300MHz for the CPU, while Linksys has overclocked the CPU to 354MHz. Along with the low-airflow case design, this can cause excessive heat and reduce routing performance. It may also responsible for many of the wireless issues reported in the forum. It is suggested that you set the CPU clock to 300MHz or improving cooling via airflow improves and/or adding a heatsink. Airflow can be improved by drilling cooling holes, or more easily by adding rubber footing on the bottom of the unit.
To set the clock speed to 300 MHz, use telnet, SSH, or Admin->Commands to run the following:
nvram set clkfreq=300,150,75 nvram commit reboot
- Note: telnet/ssh user is root, and password is same as the GUI
- In the GUI Commands, run each line separately, or separate the commands with a semicolon.
The reset button and low NVRAM (e.g. for openVPN) issues can be fixed by using buddee's WRT320N conversion to an E2000 forum thread.